D-Power E-TERNITY² V300 - 300cm electric glider full GRP ARF+

D-Power E-TERNITY² V300 - 300 cm electric glider, fully GRP ARF+ DPETV300V2

Item no.: DPETV300V2
EAN: 4251014793815

In 2018, D-Power launched its first fully GRP gliders with the E-TERNITY series. Following this great success, the successor series is now available: E-TERNITY² - now in ARF+ configuration with a significantly higher degree of prefabrication. In addition, the E-TERNITY² now comes in a new, uniform, stylish colour design.

All-round flight characteristics
The E-TERNITY² V300 has excellent all-round characteristics thanks to its aerodynamic design and modified wing profile. The V-tail gives the electric glider maximum stability and neutral flight behaviour. The model can be manoeuvred stably through all common aerobatic manoeuvres and also performs very well in thermals. With its top-mounted flaps, the E-TERNITY² can also be flown very slowly and landed safely.

High-quality construction
The E-TERNITY² V300 is made from a mould-painted GRP fuselage. The wings and V-tail are also made entirely from GRP. In addition, components subject to particularly high loads are reinforced with carbon. The built-in MULTIlock® wing lock gives the wings additional support and, thanks to the built-in MPX high-current connectors, the wings can be quickly removed.

High ARF+ prefabrication level
Spend minimal time in the workshop and maximum time at the airfield. The ARF+ prefabrication level takes care of the most time-consuming work for you. All cable layers are completely laid, so that electronic components only need to be connected to the finished wiring harness and the receiver. In addition, all control horns are pre-installed, the GRP motor mount for gear motors is resin-coated, and the battery tray and servo mounts are factory-installed. Construction is therefore limited to installing your preferred electronics.

Features
- Electric glider with great all-round flying characteristics
- With V-tail and top-mounted flaps
- Entirely manufactured in high-quality GRP monocoque construction
- CFRP reinforcements in fuselage and wings
- Solid carbon wing spar
- Modified RG14 wing profile
- Mould-painted GRP fuselage
- Mould-painted GRP wings with modern design
- GRP canopy
- High visibility thanks to high-contrast block stripes on the underside of the wings
- Short construction time thanks to high ARF+ prefabrication level

Features ARF+
- Wiring harness fully installed and integrated
- Resin-coated GRP motor mount for gear motors
- Fully installed servo frames
- MULTIlock® wing locking system installed
- MPX® high-current connectors installed in fuselage and wings
- Pre-turned carbon fibre linkage, all control horns pre-installed
- Laser-cut battery board pre-installed in fuselage
- Richly illustrated, German-language assembly instructions

Technical data
- Wingspan: 3000 mm
- Fuselage length: 1440 mm
- Flying weight: 2480 g (without battery)
- Wing profile: RG14 mod.
- Wing area: 57.1 dm²

Required accessories
- Motor: D-Power D-DRIVE IL28-2800 4:1 gear motor
- Controller: D-Power AVICON 50A brushless
- Battery: 4S LiPo 2200 mAh (14.8 V)
- Folding propeller: 13 x 8" @4S
- Aileron servos: 2x D-Power DS-840BBMG
- Flap servos: 2x D-Power DS-840BBMG
- V-tail servos: 2x D-Power DS-220BBMG
- Transmitter and receiver: at least 8 channels


Information on product safety
Information on product safety

Manufacturer:
D-Power
Owner: Horst Josef Derkum
Sürther Str. 92-94
50996 Cologne
Germany
Tel: +49 221 34664157
info@d-power-modellbau.com

EU authorised representative:
D-Power
Owner: Horst Josef Derkum
Sürther Str. 92-94
50996 Cologne
Germany
Tel: +49 221 34664157
info@d-power-modellbau.com